Updating node-red project API Forum - Published: Hello! I’m working on setting up a CI pipeline for our node-red project and and I would like to automate the deployment to target. I thought maybe I could use the node-red admin API. More specifically...moreHello! I’m working on setting up a CI pipeline for our node-red project and and I would like to automate the deployment to target. I thought maybe I could use the node-red admin API. More specifically the POST /flows. However, when I try to use the API all I get is this: 301 Moved Permanently 301 Moved Permanently nginx/1.20.1 Is the node-red admin API not available on the groov EPIC? Are th...... <less I want to 32 crc and 30 crc and 16 crc with my own polynomial Forum - Published: I want to 32 crc and 30 crc and 16 crc with my own polynomial ,how can I implement this using opto scripting? please reply...I want to 32 crc and 30 crc and 16 crc with my own polynomial ,how can I implement this using opto scripting? please reply... <less EtherNet/IP Configurator for Groov? Forum - Published: I’ve been experimenting this week with the EtherNet/IP Configurator for SNAP PAC hardware. Is it possible to configure similar communication for I/O attached directly to a Groov EPIC-PR1?...I’ve been experimenting this week with the EtherNet/IP Configurator for SNAP PAC hardware. Is it possible to configure similar communication for I/O attached directly to a Groov EPIC-PR1?... <less Understanding high-density channel data for streaming via UDP Forum - Published: Hello, I am trying to understand how to interrupt the high-density channel data located in the OPTOMMP starting at address FFFF F100 0300. According to the structure on page 155 of the manual, this...moreHello, I am trying to understand how to interrupt the high-density channel data located in the OPTOMMP starting at address FFFF F100 0300. According to the structure on page 155 of the manual, this section should have the analog channels value in engineering units and the feature data for digital channels. image898×508 86.9 KB For now, I am trying to read the state of a digital output from a GRV-ODCI-12 card located in slot 0. The controller is a GRV-EPIC-PR1. From looking at the Generic MMP usi...... <less A problem in TCP/IP communication Forum - Published: A R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters...moreA R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters by changing the parameters of the communication handle. The R1 controller is the client of TCP communication. To test the effectiveness of TCP communication, I set the polling interval to 100ms, so there is no need for such fast polling during normal use. R1 has been running normally for several...... <less Ignition 8, PR1 Forum - Published: I am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect,...moreI am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect, via MQTT, my remote workshop with my main workshop. In my main workshop, I have Ignition (“full platform”) 8.1.25 currently. Questions: Are there any foreseen incompatibilities publishing from 8.1.21 MQTT modules to 8.1.25? I am aware there is a “lag” between IA publishing LTS versions and Opto...... <less Data download button? Forum - Published: GroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps...moreGroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps. Is there a way to collect data in the same way, not necessarily display it in any way, then download it in larger blocks (ie, 20 different data sources for an hours data)? I’m using CODESYS on the back end of this project if that is relevant.... <less Does OPTO 22 supports OPC UA Forum - Published: Dear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov...moreDear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov EPIC system. My mail id: lokesh.akula@lotuswireless.com... <less SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
I want to 32 crc and 30 crc and 16 crc with my own polynomial Forum - Published: I want to 32 crc and 30 crc and 16 crc with my own polynomial ,how can I implement this using opto scripting? please reply...I want to 32 crc and 30 crc and 16 crc with my own polynomial ,how can I implement this using opto scripting? please reply... <less EtherNet/IP Configurator for Groov? Forum - Published: I’ve been experimenting this week with the EtherNet/IP Configurator for SNAP PAC hardware. Is it possible to configure similar communication for I/O attached directly to a Groov EPIC-PR1?...I’ve been experimenting this week with the EtherNet/IP Configurator for SNAP PAC hardware. Is it possible to configure similar communication for I/O attached directly to a Groov EPIC-PR1?... <less Understanding high-density channel data for streaming via UDP Forum - Published: Hello, I am trying to understand how to interrupt the high-density channel data located in the OPTOMMP starting at address FFFF F100 0300. According to the structure on page 155 of the manual, this...moreHello, I am trying to understand how to interrupt the high-density channel data located in the OPTOMMP starting at address FFFF F100 0300. According to the structure on page 155 of the manual, this section should have the analog channels value in engineering units and the feature data for digital channels. image898×508 86.9 KB For now, I am trying to read the state of a digital output from a GRV-ODCI-12 card located in slot 0. The controller is a GRV-EPIC-PR1. From looking at the Generic MMP usi...... <less A problem in TCP/IP communication Forum - Published: A R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters...moreA R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters by changing the parameters of the communication handle. The R1 controller is the client of TCP communication. To test the effectiveness of TCP communication, I set the polling interval to 100ms, so there is no need for such fast polling during normal use. R1 has been running normally for several...... <less Ignition 8, PR1 Forum - Published: I am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect,...moreI am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect, via MQTT, my remote workshop with my main workshop. In my main workshop, I have Ignition (“full platform”) 8.1.25 currently. Questions: Are there any foreseen incompatibilities publishing from 8.1.21 MQTT modules to 8.1.25? I am aware there is a “lag” between IA publishing LTS versions and Opto...... <less Data download button? Forum - Published: GroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps...moreGroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps. Is there a way to collect data in the same way, not necessarily display it in any way, then download it in larger blocks (ie, 20 different data sources for an hours data)? I’m using CODESYS on the back end of this project if that is relevant.... <less Does OPTO 22 supports OPC UA Forum - Published: Dear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov...moreDear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov EPIC system. My mail id: lokesh.akula@lotuswireless.com... <less SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
EtherNet/IP Configurator for Groov? Forum - Published: I’ve been experimenting this week with the EtherNet/IP Configurator for SNAP PAC hardware. Is it possible to configure similar communication for I/O attached directly to a Groov EPIC-PR1?...I’ve been experimenting this week with the EtherNet/IP Configurator for SNAP PAC hardware. Is it possible to configure similar communication for I/O attached directly to a Groov EPIC-PR1?... <less Understanding high-density channel data for streaming via UDP Forum - Published: Hello, I am trying to understand how to interrupt the high-density channel data located in the OPTOMMP starting at address FFFF F100 0300. According to the structure on page 155 of the manual, this...moreHello, I am trying to understand how to interrupt the high-density channel data located in the OPTOMMP starting at address FFFF F100 0300. According to the structure on page 155 of the manual, this section should have the analog channels value in engineering units and the feature data for digital channels. image898×508 86.9 KB For now, I am trying to read the state of a digital output from a GRV-ODCI-12 card located in slot 0. The controller is a GRV-EPIC-PR1. From looking at the Generic MMP usi...... <less A problem in TCP/IP communication Forum - Published: A R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters...moreA R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters by changing the parameters of the communication handle. The R1 controller is the client of TCP communication. To test the effectiveness of TCP communication, I set the polling interval to 100ms, so there is no need for such fast polling during normal use. R1 has been running normally for several...... <less Ignition 8, PR1 Forum - Published: I am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect,...moreI am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect, via MQTT, my remote workshop with my main workshop. In my main workshop, I have Ignition (“full platform”) 8.1.25 currently. Questions: Are there any foreseen incompatibilities publishing from 8.1.21 MQTT modules to 8.1.25? I am aware there is a “lag” between IA publishing LTS versions and Opto...... <less Data download button? Forum - Published: GroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps...moreGroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps. Is there a way to collect data in the same way, not necessarily display it in any way, then download it in larger blocks (ie, 20 different data sources for an hours data)? I’m using CODESYS on the back end of this project if that is relevant.... <less Does OPTO 22 supports OPC UA Forum - Published: Dear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov...moreDear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov EPIC system. My mail id: lokesh.akula@lotuswireless.com... <less SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Understanding high-density channel data for streaming via UDP Forum - Published: Hello, I am trying to understand how to interrupt the high-density channel data located in the OPTOMMP starting at address FFFF F100 0300. According to the structure on page 155 of the manual, this...moreHello, I am trying to understand how to interrupt the high-density channel data located in the OPTOMMP starting at address FFFF F100 0300. According to the structure on page 155 of the manual, this section should have the analog channels value in engineering units and the feature data for digital channels. image898×508 86.9 KB For now, I am trying to read the state of a digital output from a GRV-ODCI-12 card located in slot 0. The controller is a GRV-EPIC-PR1. From looking at the Generic MMP usi...... <less A problem in TCP/IP communication Forum - Published: A R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters...moreA R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters by changing the parameters of the communication handle. The R1 controller is the client of TCP communication. To test the effectiveness of TCP communication, I set the polling interval to 100ms, so there is no need for such fast polling during normal use. R1 has been running normally for several...... <less Ignition 8, PR1 Forum - Published: I am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect,...moreI am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect, via MQTT, my remote workshop with my main workshop. In my main workshop, I have Ignition (“full platform”) 8.1.25 currently. Questions: Are there any foreseen incompatibilities publishing from 8.1.21 MQTT modules to 8.1.25? I am aware there is a “lag” between IA publishing LTS versions and Opto...... <less Data download button? Forum - Published: GroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps...moreGroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps. Is there a way to collect data in the same way, not necessarily display it in any way, then download it in larger blocks (ie, 20 different data sources for an hours data)? I’m using CODESYS on the back end of this project if that is relevant.... <less Does OPTO 22 supports OPC UA Forum - Published: Dear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov...moreDear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov EPIC system. My mail id: lokesh.akula@lotuswireless.com... <less SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
A problem in TCP/IP communication Forum - Published: A R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters...moreA R1 controller and 10 temperature and humidity modules communicate through Ethernet. The control strategy in R1 uses an Ethernet communication handle to connect different temperature and humidity meters by changing the parameters of the communication handle. The R1 controller is the client of TCP communication. To test the effectiveness of TCP communication, I set the polling interval to 100ms, so there is no need for such fast polling during normal use. R1 has been running normally for several...... <less Ignition 8, PR1 Forum - Published: I am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect,...moreI am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect, via MQTT, my remote workshop with my main workshop. In my main workshop, I have Ignition (“full platform”) 8.1.25 currently. Questions: Are there any foreseen incompatibilities publishing from 8.1.21 MQTT modules to 8.1.25? I am aware there is a “lag” between IA publishing LTS versions and Opto...... <less Data download button? Forum - Published: GroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps...moreGroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps. Is there a way to collect data in the same way, not necessarily display it in any way, then download it in larger blocks (ie, 20 different data sources for an hours data)? I’m using CODESYS on the back end of this project if that is relevant.... <less Does OPTO 22 supports OPC UA Forum - Published: Dear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov...moreDear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov EPIC system. My mail id: lokesh.akula@lotuswireless.com... <less SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Ignition 8, PR1 Forum - Published: I am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect,...moreI am setting up a PR1 with Ignition 8 Edge for R&D. I am aware that the PR1 can run 8, and have downloaded the latest PR1 8 image from the Opto site. This has Ignition Edge 8.1.21. My goal is to connect, via MQTT, my remote workshop with my main workshop. In my main workshop, I have Ignition (“full platform”) 8.1.25 currently. Questions: Are there any foreseen incompatibilities publishing from 8.1.21 MQTT modules to 8.1.25? I am aware there is a “lag” between IA publishing LTS versions and Opto...... <less Data download button? Forum - Published: GroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps...moreGroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps. Is there a way to collect data in the same way, not necessarily display it in any way, then download it in larger blocks (ie, 20 different data sources for an hours data)? I’m using CODESYS on the back end of this project if that is relevant.... <less Does OPTO 22 supports OPC UA Forum - Published: Dear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov...moreDear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov EPIC system. My mail id: lokesh.akula@lotuswireless.com... <less SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Data download button? Forum - Published: GroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps...moreGroovView Trend gadgets have a button to Download Trend data. However, they’re limited to four traces per gadget and if you download data from multiple gadgets you have to manually align the timestamps. Is there a way to collect data in the same way, not necessarily display it in any way, then download it in larger blocks (ie, 20 different data sources for an hours data)? I’m using CODESYS on the back end of this project if that is relevant.... <less Does OPTO 22 supports OPC UA Forum - Published: Dear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov...moreDear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov EPIC system. My mail id: lokesh.akula@lotuswireless.com... <less SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Does OPTO 22 supports OPC UA Forum - Published: Dear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov...moreDear Opto 22 team, We are a partner of OPTO22, We are looking for some information related to OPTO 22 OPC UA . Kindly provide the details of Maximum number of Tags and Clients can be connected to groov EPIC system. My mail id: lokesh.akula@lotuswireless.com... <less SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
SoftPAC modbus port Forum - Published: Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default....Is it someway possible to change the default modbus port on SoftPac to something other than 502? I’ve tried changing it in PAC Manager but it keeps going back to default.... <less Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Ethernet Communications Loss - Plantwide Shutdown Forum - Published: Hello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s...moreHello, I’m new to Opto22, so this might be a basic question, but… Currently I have a plant network composed of multiple PR1s. The ‘Main’ PR1 is running a control engine sending commands to the other PR1s in normal operation. Every device (PLCs etc.) in the plant is routed through an ethernet switch. My question is, how would you handle a plant shutdown if the switch lost power, so there was no communications between any of the PLCs? Is there a way to run a control engine on each individual contr...... <less Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Wrap text in PAC Display Forum - Published: Is there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I...moreIs there any way to display a string from the control engine in PAC Display split accross more than one line? I’ve used OptoScript to include CR and LF characters, and while they are present when I examine the ASCII for the string, they don’t DO anything in the window - the text stubbornly remains on one line, until it exceeds the window size. While we’re at it, the ability to wrap text in STATIC text boxes would also be extremely helpful.... <less Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Codesys Online Error Forum - Published: Hi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652...moreHi, I am trying to download CodeSys program into groov RIO, but seem like the Opto22 Library having some issue. Anyone experience this before? image1323×938 61.8 KB image1631×1014 65.9 KB image1652×1012 81.2 KB My CodeSys Version as below: image908×487 56.9 KB Thank you... <less Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov EPIC Permissions Forum - Published: I’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices...moreI’m wondering if there are any plans to expand the user classes for Groov EPIC devices. I would like to create a user account for my maintenance crew to use when troubleshooting issues with I/O devices. The only way, as far as I can tell, to give them access to the I/O through the browser or app is to make that user a System-wide Administrator, which isn’t something I want to do. Am I missing something? ... <less J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
J1939 with EPIC CCANI-2 module Forum - Published: I’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s...moreI’m having some trouble getting J1939 messages in Codesys using EPIC. I know it isn’t officially supported but I’m hoping someone can point me in the right direction. I started out with greichert’s sample project and am now injecting two signals, RPM and Coolant Temp which is being read ok with a murphy PV101 on the same bus but I don’t get anything on the EPIC. Codesys shows the CANBUS reading the telegrams but no values. I’ve searched thru the Codesys forums and web for a solution and can’t fi...... <less Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov view - 500 server error Forum - Published: When I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different...moreWhen I try to copy paste any gadgets i get 500 server error. Does anyone face this issue. How it clear this error? Update: Found the issue. When i copy gadgets from other window and paste to different window the handheld page height increases with huge space between each gadgets vertically. I think i had copied more than 100+ gadgets(Multiple times) at same time which lead to increase of handheld pafe height enormously. Lead to programming error. image735×264 14.7 KB... <less Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Modern Browser Woes Forum - Published: Hows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be...moreHows it going everyone? Got another odd complication Im running into, doesnt seem to be an Opto problem in this case but Im wondering if anyone else has run into this and if so any advice that can be offered would be highly appreciated. System is running a PR1 and Groov View, a Teguar touchscreen IPC with Windows LTSC on it, and thats it. When I got the PO I did what I always do, grab the IPC, update windows and download the latest Chrome build. Built the system, tested the logic and deployed. G...... <less RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
RIO MQTT set up & validation error in: MqttString.java Forum - Published: Hi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol...moreHi Opto22 folks, I am unable to get a connection validated to our MQTT broker (Solace). I am not using SSL, authentication or certs, etc. ERROR|2023-12-05 13:25:39,409|MqttString.java|805|MQTT protocol connection attempt to broker failed waiting for validation tcp://10.29.1.224:1883. The logs indicate that the connection is made, etc. The RIO tools can ping & detect the IP addr and open port 1883. I have a home lab set up where there are no issues with the OPTO22 RIO. The home broker is Mosquitt...... <less Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Reading Controller information groove epic Forum - Published: Hi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die...moreHi, Is it possible to read system status information like temperature cpu load etc…? We would like to create a device monitoring view in a scada system. I’ve found the forum: “Flow to get CPU die temperature from EPIC PR1” so i can retrieve the CPU temperature using node-red ( cat /sys/devices/virtual/thermal/thermal_zone0/temp ), however I can’t find the location of other data.... <less Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Can't Find Where Palette Write File is Actually Saved Forum - Published: Hello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path...moreHello, I am new to Node Red and cannot find where a simple text file is written to when using the node Write File. I am just using 4 nodes, an inject, write file, read file, and debug with the path to C:\Test1.txt. It executes fine and I see in the debug window that every time it does an additional 7 appears. The problem is when looking in the same directory using explorer it does not exist. I know there is a file saved somewhere for when I change the action from append to file to DELETE FI...... <less Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov View Page Library Forum - Published: I have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel...moreI have 20+ pages to build from scratch. Not too good with groov build yet. Anyone has already some pages that are willing to share? I want to see what the community is capable of. Looking for: Diesel engine parameters Water Pumping and chilling. Air compressor. Water temperature.... <less EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
EPIC lost communication / won't turn back on Forum - Published: Tried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a...moreTried turning on one of our EPICs after a period of being powered down… all modules are red, the power is red, but no indicator on the status, and the touchscreen will not turn on. It was reset with a paperclip but still all red, and it’s been left in that state for a while but no changes. Section 3 of the EPIC manual says the red on the power LED indicates it’s resetting, but it seems stuck in the reset? It never turns green! And the Status LED doesn’t go green nor red. And there wasn’t anythin...... <less CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
CONNECTION ISSUE: GROOV RIO and PAC CONTROLLER Forum - Published: I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error....I’m trying to connect my PAC controller to my Groov RIO device through Ethernet and followed all steps for that, still it’s not allowing me to connect and flashing an error code: 10057 showing Enternet Socket Error.... <less MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
MMP address change doesnt reflect on pac control Forum - Published: Why changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is...moreWhy changes made through mmp address doesn’t change change pac control. Ex. I changed the channel type for rio through mmp address but it doesnt make any change in pac control io configuration. Is there a way where mmp change can reflect on pac control?... <less Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Fuel sender 33-240 Ohm connection Forum - Published: We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?...We need to find the best way to connect our standard 33-240 Ohm fuel sender to any groov epic card. Curently wondering if we can use a rtd card. Anyone has tried anything?... <less CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
CODESYS structured text priority and syntax Forum - Published: I’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those...moreI’ve got a CODESYS project connected to my groov that’s not acting how I expect. I have a structured text POU like this: IF TestInput THEN TestOutput := TRUE; ELSE TestOutput := FALSE; END_IF Those two variables are GRV_OMRIS_8 channels: Screenshot 2023-11-15 at 10.28.42 AM855×218 20.3 KB I expect that if I go into Groov Manage and toggle TestInput to “On”, that this code should turn TestOutput to “On”. Instead, what I see is that it forces TestInput back to “Off” immediately, and TestOutput ...... <less « PreviousPage 3 of 10Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items