SNAP-AIRATE-HFi
Hover over image to zoom in

SNAP-AIRATE-HFi

$347.00 (USA and Canada only)

Availability: Call for Availability
SNAP Isolated 2-Ch Analog Frequency Input, 2 Hz to 500 kHz or 20 Hz to 500 kHz

Production Specification

The SNAP-AIRATE-HFi module provides frequency to digital conversion. Each of the two isolated channels can be configured for a 0.1-second measurement interval, providing an input range of 20 Hz to 500 kHz, or a 1-second measurement interval, providing an input range of 2 Hz to 500 kHz.

Nine volts through a 3.6 kOhm pull-up resistor is provided internally for each channel for use with devices that have open-collector outputs. This feature eliminates the need for you to provide the pull-up voltage supply and associated wiring, barrier strips, and so on. The module works with TTL, CMOS, and open-collector outputs.

All SNAP analog modules are transformer isolated as well as optically isolated from all other modules and from the I/O processor. In addition, this module provides channel-to-channel isolation. Since the two channels do not share any common connections, grounded sensors and field devices may be used with them.

The SNAP-AIRATE-HFi mounts on a SNAP PAC rack and works with all SNAP PAC rack-mounted controllers and brains with SNAP PAC firmware version 9.3e or higher.

Input Range

2 Hz - 500 kHz at 1.0 s Data Freshness
20 Hz - 500 kHz at 0.1 s Data Freshness

Input Voltage Range
 Sine wave >= 2000 Hz
 Sine wave at 200 Hz
 Sine wave at 20 Hz
 Sine wave at 2 Hz
 Square wave
 Maximum survivable

 

3.0 V to 48 Vp-p
4.0 V to 48 Vp-p
5.0 V to 48 Vp-p
17 V to 48 Vp-p
3.0 V to 48 Vp-p
110 Vp-p

Input Impedance

55 kOhms

Input Coupling

Single-ended AC

Pull-up Voltage

6 to 9 VDC

Pull-up Resistor

3.6 kOhm

Minimum Pulse Width

1 microsecond

Data Freshness*

0.1 s at 20 Hz - 500 kHz
1.0 s at 2 Hz to 500 kHz

Resolution (Hz)

f / (48,000,000 * Data Fresh­ness), where is the current fre­quency measurement

Accuracy (at 1.0 s Data Freshness)

+- 0.005% of input for input greater than 500 Hz
+- 0.005% of input plus an additional +- 0.006 Hz for input less than 500 Hz

Maximum Operating Common Mode Voltage

250 V Continuous
1500 V Transient

DC Common Mode Rejection

> -120 dB

AC Common Mode Rejection

> -120 dB at 60 Hz

Isolation: Channel to Channel

250 V Continuous
1500 V Transient

Power Consumption

1.05 W (210 mA @ 5 V)

Ambient Temperature
 Operating
 Storage

 

-20 to 70 °C
-40 to 85 °C

Humidity

5-95%, non-condensing

Torque, hold-down screws

Not to exceed 1 in-lb (0.11 N-m)

Torque, connector screws

5.22 in-lb (0.59 N-m)

Wire size range

22 to 14 AWG

Agency Approvals

CE, RoHS, DFARS; UKCA

Warranty

Lifetime

* User selectable. Default is 0.1 seconds.

SNAP Isolated Analog Input Modules Data Sheet

The isolated analog input modules described in this document are part of Opto 22's SNAP PAC System. They provide optical isolation, transformer isolation, and channel-to-channel isolation. This data sheet covers the following part numbers:

UKCA Declaration of Conformity (EMC, LVD, RoHS)

This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with the rules, regulations and standards of the United Kingdom. The models cited have been tested to the essential requirements listed in the Standards section, and fully comply with the legislation as listed in UK Legislation section.

Declaration of Conformity (EMC, LVD, RoHS)

This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with European, international, and/or national standards and regulations.

Opto 22 RoHS 3 Statement of Compliance - Restriction of Hazardous Substances

This document is a statement of compliance with the EU Directive 2015/863/EU, Restriction of Hazardous Substances (RoHS 3). This document lists Opto 22 products that comply with the substance restrictions of the RoHS 3 directive.

UL Approval Document

This document lists all Opto 22 part numbers that have the Underwriters Laboratory (UL) approval.

CE Declaration: EMC

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.

CE Declaration: Low Voltage

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.

No downloads are available for this product.

Video: SNAP PAC System Overview

This overview describes the four integrated components of the SNAP PAC system: software, controllers, brains and I/O. This hardware and software system is designed for industrial control, remote monitoring and data acquisition.