SNAP-AIRATE
Hover over image to zoom in

SNAP-AIRATE

Availability: Obsolete
OBSOLETE SNAP 2-Ch 0-25,000 Hz Analog Rate Input Module

Production Specification

*** NOTE: Due to the unavailability of essential parts, this product is obsolete and no longer available. For a replacement, consider the SNAP-AIRATE-HFi, which also offers channel-to-channel isolation. ***

The SNAP-AIRATE provides two channels of frequency-to-digital conversion at 0-25,000 Hz. Nine volts through a 4.7 K Ohm pull-up resistor are provided internally for use with devices that have open collector outputs. The module works with TTL, CMOS, and open collector outputs and is ideally suited for use with a tachometer.

Part of the SNAP PAC System, the module mounts on a SNAP PAC rack with a SNAP PAC brain or rack-mounted controller. Analog, digital, and serial I/O modules can all be on the same rack. Such an I/O unit is also well suited for PC-based control or for use as intelligent remote I/O for an Allen-Bradley Logix PLC system, such as ControlLogix, MicroLogix, or CompactLogix.

Build your system in the SNAP I/O Configurator.
*** NOTE: Due to the unavailability of essential parts, this product is obsolete and no longer available. For a replacement, consider the SNAP-AIRATE-HFi, which also offers channel-to-channel isolation. ***

Nominal Input Range

0 to 25,000 Hz

Input Over-Range

To 27,500 Hz

Resolution

1 Hz

Input Response Time(% of span / delta Hz / delta time)

10.0% / 2,500 Hz / 0.1 sec
63.2% / 15.8 K Hz / 0.9 sec
99.0% / 24.75 K Hz / 4.2 sec

Data Freshness (Max)

126 ms

DC Common Mode Rejection

> -120 dB

AC Common Mode Rejection

> -120 dB at 60 Hz

Maximum Operating Common Mode Voltage

250 V

Accuracy (% full scale)

±4 Hz or ±0.5% of the input fre­quency (whichever is greater)

Drift: Gain Temperature Coeffi­cient

200 ppm / °C

Drift: Offset Temperature Coef­ficient

50 ppm / °C

Input Coupling

Single-ended AC (capacitor coupled)

Input Amplitude
Sine wave
Square wave

 

2.5 V to 24 V p-p
0.5 V to 24 V p-p

Minimum Pulse Width

18 microseconds

Input Impedance (Inputs share the same reference point.)
Pull-up Voltage
Pull-up Resistor

50 K ohms AC coupled
(-input to +input)
6 to 9 V
4.7 K ohms

Isolation

1500 V

Power Requirements

5 VDC (±0.15 V) at 190 mA

Operating Temperature

-20 °C to 70 °C

Storage Temperature

-40 °C to 85 °C

Humidity

5-95%, non-condensing

Wire size

22 to 14 AWG

Torque, hold-down screws

Not to exceed 1 in-lb (0.11 N-m)

Torque, connector screws

5.22 in-lb (0.59 N-m)

Agency Approvals

UL, CE, RoHS, DFARS; UKCA

Warranty

Lifetime

SNAP Analog Input Modules Data Sheet

SNAP I/O analog input modules are part of Opto 22's SNAP PAC System. This document includes descriptions, specifications, and wiring and dimensional diagrams for the following analog input modules:

For analog modules with channel-to-channel isolation, see Form 1182, the SNAP Isolated Analog Input Modules Data Sheet.

SNAP PAC System Product Guide

This document lists and describes all current Opto 22 SNAP PAC System part numbers, including PAC Project software, SNAP PAC controllers, and SNAP I/O modules of all kinds. SNAP PAC mounting racks and SNAP power supplies are also listed.

UKCA Declaration of Conformity (EMC, LVD, RoHS)

This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with the rules, regulations and standards of the United Kingdom. The models cited have been tested to the essential requirements listed in the Standards section, and fully comply with the legislation as listed in UK Legislation section.

Declaration of Conformity (EMC, LVD, RoHS)

This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with European, international, and/or national standards and regulations.

Opto 22 RoHS 3 Statement of Compliance - Restriction of Hazardous Substances

This document is a statement of compliance with the EU Directive 2015/863/EU, Restriction of Hazardous Substances (RoHS 3). This document lists Opto 22 products that comply with the substance restrictions of the RoHS 3 directive.

UL Approval Document

This document lists all Opto 22 part numbers that have the Underwriters Laboratory (UL) approval.

CE Declaration: Component

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.

CE Declaration: EMC

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.

CE Declaration: Low Voltage

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with the mentioned European, international and/or national standards and regulations.

CAD Drawing: SNAP I/O Module

This CAD file includes drawings that apply to most SNAP analog and digital I/O modules.

Video: SNAP PAC System Overview

This overview describes the four integrated components of the SNAP PAC system: software, controllers, brains and I/O. This hardware and software system is designed for industrial control, remote monitoring and data acquisition.

Video: Securing SNAP Module

A quick overview on securing a SNAP Module to a SNAP rack.

Video: Removing a SNAP Module

A quick overview on removing a SNAP module.

Accuracy vs Resolution

What's the difference between accuracy and resolution in analog I/O specifications? Try your own specs in the calculator.