Opto 22

43044 Business Park Drive, Temecula, CA 92590 USA
Local & outside the USA:(951) 695-3000
Toll-Free within the USA:(800) 321-6786
Fax: (951) 695-3095
Email: sales@opto22.com
 
KB86078
Clearing configured breakpoints should also clear "Break On" flag
Revision:  2.0
Published:  8/16/2016
Applies To
SNAP-PAC-S1
SNAP-PAC-S1-FM
SNAP-PAC-S1-W
SNAP-PAC-S2
SNAP-PAC-S2-W
SNAP-PAC-R1
SNAP-PAC-R1-FM
SNAP-PAC-R1-W
SNAP-PAC-R1-B
SNAP-PAC-R2
SNAP-PAC-R2-FM
SNAP-PAC-R2-W
SOFTPAC
Versions
Problem was discovered in version:  
Firmware R9.5a
Problem is fixed in version:  
Firmware R9.5b

SYMPTOMS

If you have configured breakpoints in your PAC Control strategy, when you switch from PAC Control debug mode to configure mode, a dialog box asks if you would like to clear all breakpoints. If you choose yes:

  • All breakpoints are cleared
  • The "Break On" flag should also be cleared
However, the "Break On" flag is not being cleared.

Because of this, every subsequent transition into debug mode (with the same strategy), shows the "Break On" indicator, even though no breakpoints are configured. And every subsequent transition from debug to config mode results in a dialog asking if all breakpoints should be cleared, even though there are no breakpoints configured.

WORKAROUND

You can clear the "Break On" flag by downloading  a different strategy or restarting the controller.

RESOLUTION

Opto 22 has resolved this issue.

Relevant Downloads
No relevant downloads have been specified.
Questions? Contact Opto 22 Product Support.
Phone: 800-835-6786 or 951-695-3080
Email: support@opto22.com

DISCLAIMER

This Opto 22 Knowledge Base ('OptoKB') article is intended to provide general technical information on a particular subject or subjects and is not an exhaustive treatment of such subjects. Accordingly, the information in this OptoKB article is not intended to constitute application, design, software, or other professional engineering advice or services. Opto 22 may modify the OptoKB articles at any time. Before making any decision or taking any action which might affect your equipment, you should consult a qualified professional.

OPTO 22 DOES NOT WARRANT THE COMPLETENESS, TIMELINESS, OR ACCURACY OF THE DATA CONTAINED IN THIS OPTOKB ARTICLE AND MAY MAKE CHANGES THERETO AT ANY TIME AT ITS SOLE DISCRETION WITHOUT NOTICE. FURTHER, ALL INFORMATION CONVEYED HEREBY IS PROVIDED TO USERS 'AS IS.' IN NO EVENT SHALL OPTO 22 BE LIABLE FOR ANY DAMAGES OF ANY KIND INCLUDING DIRECT, INDIRECT INCIDENTAL, CONSEQUENTIAL, LOSS PROFIT, OR DAMAGE, EVEN IF OPTO 22 HAS BEEN ADVISED ON THE POSSIBILITY OF SUCH DAMAGES.

OPTO 22 DISCLAIMS ALL WARRANTIES WHETHER EXPRESSED OR IMPLIED WITH RESPECT TO THE INFORMATION (INCLUDING HARDWARE, SOFTWARE, AND/OR FIRMWARE) PROVIDED HEREBY, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE, MERCHANTIBILITY, AND NON-INFRINGEMENT. Note that certain jurisdictions do not sanction the exclusion of implied warranties: thus, this disclaimer may not apply to you.

Copyright © 2017 Opto 22. All rights reserved.

My.Opto22

All Opto22

Request Information
  • FREE Product Brochure
  • Product Demonstration
  • PreSales Engineering Assistance

Opto 22 Product Support

Opto 22 Product Support is FREE Monday through Friday 7 a.m. to 5 p.m. Pacific Time

Product Support Numbers:

Local: (951) 695-3080
Toll-Free: (800) 835-6786
Fax: (951) 695-3017
support@opto22.com

Products

None

Downloads

None

Documents

None